930M Ag Handler Small Wheel Loader

Photos

Operating Weight
31876 lb
Bucket Capacities
3.1-5.0 m3 (4.0-6.5 yd3)
Maximum Gross Power – ISO 14396 (Standard Power Mode; Speed Range 1-3*)
160 hp
Maximum Gross Power – ISO 14396 (DIN) (Standard Power Mode; Speed Range 1-3*)
162 hp

Specs

Weights

Operating Weight
31876lb
Operating Weight
31382lb

Buckets

Bucket Capacities
3.1-5.0 m3 (4.0-6.5 yd3)
Bucket Capacities – Light Material
3.1-5.0 m3 (4.0-6.5 yd3)
Bucket Capacities
2.1-5.0 m³ (2.7-6.5 yd³)
Bucket Capacities - Light Material
3.1-5.0 m³ (4.0-6.5 yd³)

Engine

Maximum Gross Power – ISO 14396 (Standard Power Mode; Speed Range 1-3*)
160hp
Maximum Gross Power – ISO 14396 (DIN) (Standard Power Mode; Speed Range 1-3*)
162hp
Rated Net Power at 1,600 rpm – SAE J1349 (Standard Power Mode; Speed Range 1-3*)
154hp
Rated Net Power at 1,600 rpm – SAE J1349 at Maximum Fan Speed (Standard Power Mode; Speed Range 1-3*)
141hp
Engine Model
Cat C7.1 ACERT
Rated Net Power at 1,600 rpm – ISO 9249 (DIN) (Standard Power Mode; Speed Range 1-3*)
158hp
Maximum Rated Gross Power - ISO 14396
168HP
Rated Net Power - 1,600 rpm - ISO 9249 (DIN) (Standard Power Mode: Speed Range 1-3*)
158HP
Maximum Net Torque - SAE J1349 (Standard Power Mode; Speed Range 1-3*)
566ft·lbf
Maximum Net Torque - ISO 9249 (1977)/EEC 80/1269 (Standard Power Mode; Speed Range 1-3*)
572ft·lbf
Displacement (Standard Power Mode; Speed Range 1-3*)
427in3
Maximum Gross Power - Maximum Engine Speed (Performance Power Mode: Range 1-4)
1800r/min
Maximum Gross Power – ISO 14396 (Performance Power Mode; Speed Range 1-4)
164hp
Maximum Gross Power – ISO 14396 (DIN) (Performance Power Mode; Speed Range 1-4)
166hp
Rated Net Power at 1,800 rpm – SAE J1349 (Performance Power Mode; Speed Range 1-4)
157hp
Rated Net Power - 1,800 rpm - SAE J1349 (Performance Power Mode: Speed Range 1-4)
157HP
Rated Net Power - 1,800 rpm - ISO 9249 (DIN) (Performance Power Mode: Speed Range 1-4)
162HP
Maximum Gross Torque – ISO 14396 (Performance Power Mode; Speed Range 1-4)
592lbf-ft
Maximum Net Torque - SAE J1349 (Performance Power Mode; Speed Range 1-4)
566ft·lbf
Maximum Net Torque - ISO 9249 (1977)/EEC 80/1269 (Performance Power Mode; Speed Range 1-4)
572ft·lbf
Displacement (Performance Power Mode; Speed Range 1-4)
427in3
Emissions
Engine meets Tier 4 Final emission standards.
Note
Net power shown is the power available at the flywheel when the engine is equipped with alternator, air cleaner and diesel exhaust filter.
Maximum Gross Power
164hp
Note
Spark arrester performance as standard – Meets the performance requirements of EN 1834-1.2000 (section 6.4.2 Visual Test) and U.S. Forestry Service SAE J350.
Note
*Range 4 power is boosted to be the same as Performance Mode.
Engine Model
Cat® C7.1
Maximum Gross Power - ISO 14396 (DIN) (Standard Power Mode: Range 1-3*)
162HP
Maximum Gross Power - ISO 14396 (Standard Power Mode: Range 1-3*)
160HP
Maximum Gross Power - Maximum Engine Speed (Standard Power Mode: Range 1-3*)
1600r/min
Rated Net Power - 1,600 rpm - SAE J1349 (Standard Power Mode: Speed Range 1-3*)
154HP
Rated Net Power - 1,600 rpm - SAE J1349 at Maximum Fan Speed (Standard Power Mode; Speed Range 1-3*)
141HP
Maximum Gross Power
168HP
Displacement (Performance Power Mode: Speed Range 1-4)
428in³
Displacement (Standard Power Mode: Speed Range 1-3*)
427in³
Emissions
Engine meets U.S. EPA Tier 4 Final emission standards.
Maximum Gross Power - ISO 14396 (DIN) (Performance Power Mode: Range 1-4)
170HP
Maximum Gross Power - ISO 14396 (Performance Power Mode: Range 1-4)
168HP
Maximum Gross Torque - ISO 14396 (Performance Power Mode: Range 1-4)
601ft·lbf
Maximum Gross Torque - ISO 14396 (Standard Power Mode: Range 1-3*)
592ft·lbf
Note (1)
*The Cat C7.1 engine meets U.S. EPA Tier 4 Final/EU Stage V emission standards.
Bore (Standard Power Mode: Range 1-4)
4.1in
Note (2)
**Range 4 power and torque is equal to Performance Mode with Caterpillar Power by Range technology.
Note (3)
Net power ratings are tested at the reference conditions for the specified standard and denote power available at the flywheel when the engine is equipped with alternator, air cleaner, emission components and fan at specified speed.
Rated Net Power - 1,800 rpm - SAE J1349 at Maximum Fan Speed (Performance Power Mode; Speed Range 1-4)
143HP
Stroke - Performance Power Mode: Range 1-4
5.3in
Maximum Net Torque - SAE J1349 (Performance [HP+] Power Mode: Range 1-4)
797N·m
Note (4)
No derating required up to 3000 m (10,000 ft) altitude. Auto derate protects hydraulic and transmission systems.
Net Power - ISO 9249 at Minimum Fan Speed (Standard Power Mode: Range 1-3**)
156HP
Stroke (Standard Power Mode: Range 1-3**)
5.3in
Net Power - SAE J1349 at Minimum Fan Speed (Standard Power Mode: Range 1-3**)
156HP
Maximum Gross Power - Maximum Engine Speed (Standard Power Mode: Range 1-3**)
1600r/min
Net Power - ISO 9249 (metric) at Minimum Fan Speed (Performance Power Mode: Range 1-4)
166HP
Net Power - ISO 9249 at Minimum Fan Speed (Performance Power Mode: Range 1-4)
164HP
Net Power - ISO 9249 (metric) at Minimum Fan Speed (Standard Power Mode: Range 1-3**)
158HP
Bore (Standard Power Mode: Range 1-3**)
4.1in
Maximum Net Torque - ISO 9249 (Performance Power Mode: Range 1-4)
587ft·lbf
Maximum Gross Torque - ISO 14396 (Standard Power Mode: Range 1-3**)
795N·m
Maximum Net Torque - ISO 9249 (Standard Power Mode: Range 1-3**)
776N·m
Net Power - SAE J1349 at Minimum Fan Speed (Performance Power Mode: Range 1-4)
163HP
Displacement (Standard Power Mode: Range 1-3**)
428in³
Maximum Gross Power - ISO 14396 (Standard Power Mode: Range 1-3**)
160HP
Maximum Gross Power - ISO 14396 (metric) (Standard Power Mode: Range 1-3**)
162HP
Maximum Net Torque - SAE J1349 (Standard Power Mode: Range 1-3**)
573ft·lbf
Maximum Rated Gross Power - ISO 14396 (metric)
170mhp

Steering

Steering Articulation Angle (each direction)
40°
Steering Cycle Times (full left to full right): At 1,800 rpm: 90 rpm steering wheel speed
2.4seconds
Number of Steering Wheel Turns – full left to full right or full right to full left
3.5turns
Maximum Flow – Steering Pump
34gal/min
Maximum Working Pressure – Steering Pump
3500psi
Maximum Steering Torque: 0 degrees (straight machine)
37155lbf-ft
Maximum Steering Torque: 40 degrees (full turn)
27747lbf-ft
Maximum Flow - Steering Pump
34gal/min
Maximum Steering Torque - 0° (Straight Machine)
37155ft·lbf
Maximum Steering Torque - 40° (Full Turn)
27747ft·lbf
Maximum Working Pressure - Steering Pump
3500psi
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left
3.5turns
Steering Articulation Angle - Each Direction
40°
Steering Cycle Times - Full Left to Full Right - At 1,800 rpm: 90 rpm Steering Wheel Speed
2.4s
Note (2)
Flow values listed are for a machine running in Performance Power Mode (1,800 rpm).
Steering Cylinder, Double Acting - Bore Diameter
2.8in
Steering Cylinder, Double Acting - Stroke
17.2in
Note (1)
Steering system uses a dedicated load sensing variable displacement pump with dual double acting cylinders.
Steering Cycle Times - Full Left to Full Right - Minimum RPM: Pump Flow Limited
2.8s
Steering Cycle Times - Full Left to Full Right - Maximum RPM: 90 rpm Steering Wheel Speed
2.4s
Steering Cylinder, Double Acting - Rod Diameter
1.6in

Loader Hydraulic System

Maximum Flow – Implement Pump
50gal/min
Maximum Flow – Implement Pump: 3rd Function Maximum Flow*
50gal/min
Maximum Flow – Implement Pump: 4th Function Maximum Flow*
42gal/min
Maximum Working Pressure – Implement Pump
4061psi
Relief Pressure – Tilt Cylinder
4351psi
Relief Pressure – Tilt Cylinder: 3rd Function Maximum Working Pressure
4061psi
Relief Pressure – Tilt Cylinder: 4th Function Maximum Working Pressure
4061psi
Hydraulic Cycle Times: Standard Mode At 1,600 rpm – Raise (ground level to maximum lift)
4.8seconds
Hydraulic Cycle Times: Standard Mode At 1,600 rpm – Dump (at maximum lift height)
1.6seconds
Hydraulic Cycle Times: Standard Mode At 1,600 rpm – Float Down (maximum lift to ground level)
1.8seconds
Hydraulic Cycle Times: Standard Mode At 1,600 rpm – Total Cycle Time
8.2seconds
Hydraulic Cycle Times: Performance Mode At 1,800 rpm – Raise (ground level to maximum lift)
4.3seconds
Hydraulic Cycle Times: Performance Mode At 1,800 rpm – Dump (at maximum lift height)
1.4seconds
Hydraulic Cycle Times: Performance Mode At 1,800 rpm – Float Down (maximum lift to ground level)
1.8seconds
Hydraulic Cycle Times: Performance Mode At 1,800 rpm – Total Cycle Time
7.5seconds
Note
*Adjustable from 20% to 100% of maximum flow through the secondary display, when equipped.
Hydraulic Cycle Time - Performance Mode at 1,800 rpm - Dump, at Maximum Lift Height
1.4s
Hydraulic Cycle Time - Performance Mode at 1,800 rpm - Float Down, Maximum Lift to Ground Level
1.8s
Hydraulic Cycle Time - Performance Mode at 1,800 rpm - Raise, Ground Level to Maximum Lift
4.3s
Hydraulic Cycle Time - Performance Mode at 1,800 rpm - Total Cycle Time
7.5s
Hydraulic Cycle Time - Standard Mode at 1,600 rpm - Dump, at Maximum Lift Height
1.6s
Hydraulic Cycle Time - Standard Mode at 1,600 rpm - Float Down, Maximum Lift to Ground Level
1.8s
Hydraulic Cycle Time - Standard Mode at 1,600 rpm - Raise, Ground Level to Maximum Lift
4.8s
Hydraulic Cycle Time - Standard Mode at 1,600 rpm - Total Cycle Time
8.2s
Maximum Flow - Implement Pump
50gal/min
Maximum Flow - Implement Pump - 3rd Function*
50gal/min
Maximum Flow - Implement Pump - 4th Function Maximum Flow*
42gal/min
Maximum Working Pressure - Implement Pump
4061psi
Note
*3rd and 4th function flow is fully adjustable from 20% to 100% of maximum flow through the secondary display.
Relief Pressure - Tilt Cylinder
4351psi
Relief Pressure - Tilt Cylinder - 3rd Function Maximum Working Pressure
4061psi
Relief Pressure - Tilt Cylinder - 4th Function Maximum Working Pressure
4061psi
Cycle Times - 1,600 rpm - Standard: Total Cycle Time
10.1s
Note (2)
Flow values listed are for a machine running in Performance Power Mode (1,800 rpm).
Cycle Times - 1,800 rpm - Performance (HP+): Dump (at Maximum Lift Height)
1.5s
Cycle Times - 1,800 rpm - Performance (HP+): Total Cycle Time
9.3s
Cycle Times - 1,600 rpm - Standard: Float Down (Maximum Lift to Ground Level)
2.7s
Cycle Times - 1,800 rpm - Performance (HP+): Raise (Ground Level to Maximum Lift)
5.1s
Cycle Times - 1,800 rpm - Performance (HP+): Float Down (Maximum Lift to Ground Level)
2.7s
Relief Pressure - Tilt Cylinder - 3rd and 4th Function Maximum Working Pressure
4061psi
Cycle Times - 1,600 rpm - Standard: Dump (at Maximum Lift Height)
1.7s
Relief Pressure - Tilt Cylinder - 3rd and 4th Function Relief Pressure
4351psi
Note (1)
Implement system uses a dedicated load sensing variable displacement pump with dual double acting lift cylinders and a single double acting tilt cylinder.
Cycle Times - 1,600 rpm - Standard: Raise (Ground Level to Maximum Lift)
5.7s
Maximum Flow - Implement Pump - 3rd Function Maximum Flow*
50gal/min
Lift Cylinder: Standard Lift Linkage - Bore Diameter
4.3in
Tilt Cylinder: Standard Lift Linkage - Stroke
21.9in
Tilt Cylinder: Standard Lift Linkage - Rod Diameter
2.8in
Lift Cylinder: Standard Lift Linkage - Rod Diameter
2.4in
Tilt Cylinder: Standard Lift Linkage - Bore Diameter
5.1in
Lift Cylinder: Standard Lift Linkage - Stroke
28.7in

Service Refill Capacities

Fuel Tank
51.5gal
Cooling System
7.9gal
Engine Crankcase
5.3gal
Transmission (gearbox)
2.2gal
Axles: Front
6.9gal
Axles: Rear
6.6gal
Hydraulic System (including tank)
43.6gal
Hydraulic Tank
23.8gal
Diesel Exhaust Fluid (DEF) Tank
5gal
Note
DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
Axles - Front
6.9gal (US)
Axles - Rear
6.6gal (US)
Cooling System
7.9gal (US)
Diesel Exhaust Fluid (DEF) Tank
5gal (US)
Engine Crankcase
5.3gal (US)
Fuel Tank
51.5gal (US)
Hydraulic System - Including Tank
43.6gal (US)
Hydraulic Tank
23.8gal (US)
Note
DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
Transmission - Gear Box
2.2gal (US)

Transmission

Forward and Reverse: Range 1*
1-13 km/h (0.6-8 mph)
Forward and Reverse: Range 2
8mph
Forward and Reverse: Range 3
17mph
Forward and Reverse: Range 4
25mph
Note
*Creeper control allows maximum speed range adjustability from 1 km/h (0.6 mph) to 13 km/h (8 mph) in Range 1 through the secondary display, when equipped. Factory default is 7 km/h (4.4 mph).
Forward and Reverse - Range 1*
1-13 km/h (0.6-8 mph)
Forward and Reverse - Range 2
8mile/h
Forward and Reverse - Range 3
17mile/h
Forward and Reverse - Range 4
25mile/h
Note
Creeper control allows maximum speed range adjustability in the forward direction from 1 km/h (0.6 mph) to 13 km/h (8 mph) in Range 1 through the secondary display when equipped. Factory default is 7 km/h (4.4 mph). Maximum reverse speed will be maintaine
Forward - Range 2
8mile/h
Forward - Range 1*
1-13 km/h (0.6-8 mph)
Reverse - Range 4
25mile/h
Reverse - Range 2
8mile/h
Forward - Range 3
17mile/h
Forward - Range 4
25mile/h
Reverse - Range 3
17mile/h
Reverse - Range 1*
8mile/h

Cab

ROPS
ISO 3471:2008
FOPS
ISO 3449:2005 Level II
Note
The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, are: – Standard cab: 68 ±3 dB(A) – Deluxe cab: 66 ±2 dB(A)
Note
*The measurements were conducted with the cab doors and windows closed and at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling fan speeds.
ROPS
ISO 3471:2008
FOPS
ISO 3449:2005 Level II
Note (1)
*The measurements were conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling fan speeds. The cab was properly installed and maintained. The measurements were conducted with the cab doors and the cab
Note (2)
*The measurements were conducted with the cab doors and windows closed and at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling fan speeds.
Declared Sound Levels - Exterior Sound Power Level (ISO 6395:2008)*
101dB(A)
Declared Sound Levels - Operator Sound Pressure Level (ISO 6396:2008)*
68dB(A)

Tires

Standard Size
20.5 R25, radial (L-3)
Other Choices Include:
20.5 R25, radial (L-2); 20.5-25 12PR (L-2); 20.5-25 12PR (L-3)
Note
Other tire choices are available. Contact your Cat dealer for details.
Note
In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
Note
Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Note (1)
Other tire choices are available. Contact your Cat dealer for details.
Note (2)
Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Note (3)
Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Other Choices Include
20.5 R25, Radial (L-2); 620/75 R26 MegaX, 750/65 R26 MegaX
Standard Size
20.5 R25, radial (L-3)

Axles

Front
Fixed; Locking differential (standard)
Rear
Oscillating ±11 degrees; Open differential (standard); Limited slip differential (optional)
Front
Fixed; Locking differential (standard)
Rear
Oscillating ±11 degrees; Open differential (standard); Limited slip differential (optional)

Dimensions and Operating Specifications (Approximate) - 3.1 m³ (4.1 yd³) Bucket

Height - Ground to Cab**
10.92ft
Height - Ground to Beacon**
12.08ft
Height - Ground Axle Center**
2.17ft
Height - Ground Clearance**
1.25ft
Length - Overall*
27.25ft
Length - Rear Axle to Bumper
6.5ft
Length - Hitch to Front Axle
4.92ft
Length - Wheel Base
9.83ft
Clearance - Bucket at 45° *
10.42ft
Clearance - Loadover Height**
11.58ft
Clearance - Level Bucket**
13.33ft
Height - Bucket Pin**
14.42ft
Height - Overall**
18.67ft
Reach - Bucket at 45°*
4.42ft
Carry Height - Bucket Pin
2ft
Dig Depth**
5.3in
Width - Bucket
9ft
Width - Tread Center
6.25ft
Turning Radius - Over Bucket
20.92ft
Width - Over Tires
8.33ft
Turning Radius - Outside of Tires
17.67ft
Turning Radius - Inside of Tires
9.33ft
Rack Angle at Full Lift
51 degrees
Dump Angle at Full Lift
44 degrees
Rack Angle at Carry
48 degrees
Departure Angle
33 degrees
Articulation Angle
40 degrees
Tipping Load - Straight - ISO 14397-1*
16430lb
Tipping Load - Full Turn - ISO 14397-1*
13934lb
Breakout*
18808lb
Operating Weight*
31876lb
Note (1)
*Vary with bucket.
Note (2)
**Vary with tire.
Note (3)
Dimensions listed are for a 930M Ag Handler High Lift configured with Fusion™ light material bucket, bolt-on cutting edge, logger/aggregate counterweights, additional guarding, 80 kg (176 lb) operator and Michelin 20.5 R25 (L-3) XHA2 tires.

Dimensions and Operating Specifications (Approximate) - 3.5 m³ (4.6 yd³) Bucket

Height - Ground to Cab**
10.92ft
Height - Ground to Beacon**
12.08ft
Height - Ground Axle Center**
2.17ft
Height - Ground Clearance**
1.25ft
Length - Overall*
27.58ft
Length - Rear Axle to Bumper
6.5ft
Length - Hitch to Front Axle
4.92ft
Length - Wheel Base
9.83ft
Clearance - Bucket at 45° *
10.17ft
Clearance - Loadover Height**
11.58ft
Clearance - Level Bucket**
13.33ft
Height - Bucket Pin**
14.42ft
Height - Overall**
19ft
Reach - Bucket at 45°*
4.67ft
Carry Height - Bucket Pin
2ft
Dig Depth**
5.3in
Width - Bucket
9ft
Width - Tread Center
6.25ft
Turning Radius - Over Bucket
21.92ft
Width - Over Tires
8.33ft
Turning Radius - Outside of Tires
17.67ft
Turning Radius - Inside of Tires
9.33ft
Rack Angle at Full Lift
51 degrees
Dump Angle at Full Lift
44 degrees
Rack Angle at Carry
48 degrees
Departure Angle
33 degrees
Articulation Angle
40 degrees
Tipping Load - Straight - ISO 14397-1*
16070lb
Tipping Load - Full Turn - ISO 14397-1*
13592lb
Breakout*
17246lb
Operating Weight*
32136lb
Note (1)
*Vary with bucket.
Note (2)
**Vary with tire.
Note (3)
Dimensions listed are for a 930M Ag Handler High Lift configured with Fusion™ light material bucket, bolt-on cutting edge, logger/aggregate counterweights, additional guarding, 80 kg (176 lb) operator and Michelin 20.5 R25 (L-3) XHA2 tires.

Power Train

Note
*Differential front locking axle can be engaged on the go at full torque to 10 km/h (6.2 mph).
Rear Axle
Oscillating
Note (2)
Power train is governed by the Caterpillar exclusive Intelligent Power Management system to deliver peak performance and efficiency.
Front Axle
Fixed
Front Axle - Traction Aid*
Locking differential standard
Rear Axle - Oscillation Angle by Tire Size - 20.5 R25
± 10.5 degrees
Brakes - Service
Inboard wet disc
Rear Axle - Traction Aid
Limited slip differential optional
Brakes - Parking
Spring applied hydraulically released
Rear Axle - Oscillation Angle by Tire Size - 750/65, 620/65
± 7 degrees

Operating Specifications

Full Turn Tip Load
19424lb

Air Conditioning System

Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.9 kg of refrigerant which has a CO2 equivalent of 2.717 metric tonnes.

Dimensions with Bucket - Standard Lift

Height - Ground Clearance**
1.3ft
Rack Angle at Carry
43°
Departure Angle
33°
Length - Wheel Base
9.8ft
Length - Rear Axle to Bumper
6.5ft
Turning Radius - Over Bucket
19.5ft
Carry Height - Bucket Pin
1.3ft
Width - Over Tires
8.3ft
Note (2)
**Vary with tire.
Dig Depth**
3.9in
Turning Radius - Outside of Tires
17.7ft
Clearance - Level Bucket**
11.75ft
Clearance - Bucket at 45°*
9.1ft
Rack Angle at Full Lift
54°
Height - Overall**
17.1ft
Width - Bucket
8.4ft
Height - Ground to Axle Center**
2.25ft
Height - Bucket Pin**
12.8ft
Operating Weight
31125lb
Width - Tread Center
6.3ft
Turning Radius - Inside of Tires
9.4ft
Reach - Bucket at 45°*
3.6ft
Length - Overall*
24.9ft
Clearance - Load over Height**
10.9ft
Length - Hitch to Front Axle
4.9ft
Height - Ground to Beacon**
12.2ft
Articulation Angle
40°
Height - Ground to Cab**
10.9ft
Note (3)
Dimensions listed are for a 930M Ag Handler configured with General Purpose 2.3 m³ (3.0 yd³) Fusion bucket, bolt-on cutting edges, heavy counterweights, 80 kg (176 lb) operator, and Michelin 20.5 R25 XHA2 tires.
Note (1)
*Vary with bucket.
Dump Angle at Full Lift
48°

Dimensions with Bucket - High Lift

Length - Rear Axle to Bumper
6.5ft
Departure Angle
33°
Height - Overall**
18.7ft
Reach - Bucket at 45°*
4.4ft
Dump Angle at Full Lift
48°
Width - Bucket
8.4ft
Length - Wheel Base
9.8ft
Width - Tread Center
6.3ft
Length - Hitch to Front Axle
4.9ft
Height - Ground to Axle Center**
2.25ft
Note (1)
*Vary with bucket.
Clearance - Bucket at 45°*
10.7ft
Height - Bucket Pin**
14.4ft
Height - Ground to Beacon**
12.2ft
Carry Height - Bucket Pin
1.9ft
Clearance - Load over Height**
11.6ft
Turning Radius - Outside of Tires
17.7ft
Turning Radius - Over Bucket
20.6ft
Rack Angle at Full Lift
51°
Rack Angle at Carry
47°
Length - Overall*
27ft
Note (2)
**Vary with tire.
Height - Ground to Cab**
10.9ft
Turning Radius - Inside of Tires
9.4ft
Clearance - Level Bucket**
13.4ft
Width - Over Tires
8.3ft
Note (3)
Dimensions listed are for a 930M Ag Handler configured with General Purpose 2.3 m³ (3.0 yd³) Fusion bucket, bolt-on cutting edges, heavy counterweights, 80 kg (176 lb) operator, and Michelin 20.5 R25 XHA2 tires.
Dig Depth**
5.3in
Articulation Angle
40°
Operating Weight
31441lb
Height - Ground Clearance**
1.3ft

Sustainability

Recyclability
94%

Features

Efficiently Powerful

Experience hybrid-like fuel efficiency with an intelligent hydrostatic power train and industry leading fuel savings through a lower maximum engine speed of just 1,600 rpm in Standard Mode. Power when you need it with Caterpillar's exclusive Power‑by-Range technology that increases power in Range 4 for improved speed on grade. For your toughest and most demanding farm applications a new Performance Mode will allow you to boost the power and hydraulic speed in all Ranges to get the job done even quicker. Meets U.S. EPA Tier 4 Final emission standards with a Cat® C7.1 engine that is designed to manage itself so you can concentrate on your work.

Experience hybrid-like fuel efficiency with an intelligent hydrostatic power train and industry leading fuel savings through a lower maximum engine speed of just 1,600 rpm in Standard Mode. Power when you need it with Caterpillar's exclusive Power‑by-Range technology that increases power in Range 4 for improved speed on grade. For your toughest and most demanding farm applications a new Performance Mode will allow you to boost the power and hydraulic speed in all Ranges to get the job done even quicker. Meets U.S. EPA Tier 4 Final emission standards with a Cat® C7.1 engine that is designed to manage itself so you can concentrate on your work.

Work Made Easy

Move more with Caterpillar's patented quick loading Performance Series buckets and High Lift optimized Z-bar linkage that combines the digging efficiency of a traditional Z-bar with tool carrier capabilities. The parallel lift and high tilt forces throughout the working range allow you to safely and confidently handle loads from bales to silage with precise control. Multi-function work has never been easier with dedicated pumps for each system and a flow sharing implement valve governed by an intelligent power management system. Simultaneously lift, steer and drive without compromise. A 20% boost in hydraulic speeds on the Ag Handler helps you finish the day on time.

Move more with Caterpillar's patented quick loading Performance Series buckets and High Lift optimized Z-bar linkage that combines the digging efficiency of a traditional Z-bar with tool carrier capabilities. The parallel lift and high tilt forces throughout the working range allow you to safely and confidently handle loads from bales to silage with precise control. Multi-function work has never been easier with dedicated pumps for each system and a flow sharing implement valve governed by an intelligent power management system. Simultaneously lift, steer and drive without compromise. A 20% boost in hydraulic speeds on the Ag Handler helps you finish the day on time.

Enjoy All Day Comfort

Have a seat in the 930M Ag Handler and enjoy automatic temperature control, class leading sound levels, excellent all around visibility and low-effort joystick controls that move with you on a fully adjustable seat suspension. A large spacious operator environment combined with Caterpillar's exclusive hydraulic cylinder damping and smooth predictable controls make this the most comfortable seat on the farm.

Have a seat in the 930M Ag Handler and enjoy automatic temperature control, class leading sound levels, excellent all around visibility and low-effort joystick controls that move with you on a fully adjustable seat suspension. A large spacious operator environment combined with Caterpillar's exclusive hydraulic cylinder damping and smooth predictable controls make this the most comfortable seat on the farm.

Customize Your Experience

Fine tune machine performance with adjustments at your fingertips through the soft touch buttons and optional secondary touch screen display. Quickly set auxiliary flow to optimize grapple or silage defacer speed, enable auto reversing fan to breathe clean in dusty environments, toggle over to fine mode for improved control when bale stacking, program linkage kick-out positions for easy feed wagon loading, adjust wheel torque to match underfoot conditions when cleaning corrals and customize ride control activation speed for a smooth loaded carry run. The 930M Ag Handler is ready for the challenge on your farm!

Fine tune machine performance with adjustments at your fingertips through the soft touch buttons and optional secondary touch screen display. Quickly set auxiliary flow to optimize grapple or silage defacer speed, enable auto reversing fan to breathe clean in dusty environments, toggle over to fine mode for improved control when bale stacking, program linkage kick-out positions for easy feed wagon loading, adjust wheel torque to match underfoot conditions when cleaning corrals and customize ride control activation speed for a smooth loaded carry run. The 930M Ag Handler is ready for the challenge on your farm!

Sustainability

  • The Cat® C7.1 engine meets U.S. EPA Tier 4 Final, EU Stage V and Korea Tier 5 emission standards.
  • Engine Idle Management System (EIMS) helps maximize fuel efficiency and reduce greenhouse gas emissions while maintaining machine performance.
  • Engine Idle Shutdown Timer reduces fuel burn, greenhouse gas emissions and unnecessary idle time by shutting down the machine after a pre-set idling period.
  • Performance Series Buckets have rounded side boards, a longer floor and open angle to carry more and load quicker so each pass is the most efficient.
  • Rimpull Control is a quick way to adjust the torque to the tires for less slipping and tire wear.
  • Cat® Production Measurement provides real-time payload weighing which help you maximize productivity, reduce fuel burn and greenhouse gas emissions, all while improving job site efficiency and lowering costs.
  • Extended maintenance intervals not only reduce downtime but decrease the amount of fluid and filters that are replaced over the life of the machine.
  • Power on Demand, transparent to the operator, provides full-time efficiency and power when you need it.
  • Tire Pressure Monitoring provides real-time tire pressure information to the operator to help increase tire wear and achieve better fuel efficiency and reduced greenhouse gas emissions.
  • Intelligent Hystat Transmission helps improves control and reduces fuel consumption and greenhouse gas emissions in load and carry applications.
  • Variable Displacement Pumps match power to load as application requirements change.
  • The Cat® C7.1 engine meets U.S. EPA Tier 4 Final, EU Stage V and Korea Tier 5 emission standards.
  • Engine Idle Management System (EIMS) helps maximize fuel efficiency and reduce greenhouse gas emissions while maintaining machine performance.
  • Engine Idle Shutdown Timer reduces fuel burn, greenhouse gas emissions and unnecessary idle time by shutting down the machine after a pre-set idling period.
  • Performance Series Buckets have rounded side boards, a longer floor and open angle to carry more and load quicker so each pass is the most efficient.
  • Rimpull Control is a quick way to adjust the torque to the tires for less slipping and tire wear.
  • Cat® Production Measurement provides real-time payload weighing which help you maximize productivity, reduce fuel burn and greenhouse gas emissions, all while improving job site efficiency and lowering costs.
  • Extended maintenance intervals not only reduce downtime but decrease the amount of fluid and filters that are replaced over the life of the machine.
  • Power on Demand, transparent to the operator, provides full-time efficiency and power when you need it.
  • Tire Pressure Monitoring provides real-time tire pressure information to the operator to help increase tire wear and achieve better fuel efficiency and reduced greenhouse gas emissions.
  • Intelligent Hystat Transmission helps improves control and reduces fuel consumption and greenhouse gas emissions in load and carry applications.
  • Variable Displacement Pumps match power to load as application requirements change.

Standard Equipment

  • Power Train
    • Auto idle shut down feature
    • Cat C7.1 engine
      • Power modes (Standard and Performance)
      • Power by range (High Power in Range 4)
      • Turbocharged and aftercooled
      • Diesel particulate filter (Fit for Life)
    • Coded start (requires secondary display)
    • Differential lock in front axle
    • Enclosed wet disc full hydraulic brakes
    • Oil sampling ports
    • Hydraulically driven demand cooling fan
    • Hydrostatic transmission with electronic control
      • Operator modes (Default, TC, Hystat™, and Ice)
      • Directional Shift Aggressiveness (fast, medium, slow)
      • Rimpull control, adjust wheel torque
      • Creeper control, adjust ground speed
    • Axle Duo-Cone™ seal guards
    • Parking brake, electric
    • Single plane cooling package wide six fins per inch density
    • Throttle lock and max speed limiter
  • Hydraulics
    • Automatic lift lower and tilt kickouts, adjustable in-cab
    • Bucket and fork modes, adjustable in-cab
    • Cylinder damping at kickout and mechanical end stops
    • Fine mode control (fast, medium, slow)
    • Hydraulic response setting (fast, medium, slow)
    • Load sensing hydraulics and steering
    • Load sensing hydraulics and steering
  • Electrical
    • Alternator, 115 amp, heavy duty
    • Batteries, 1,000 CCA (2) 24V system, disconnect switch
    • Back-up alarm
    • Halogen work and roading lights, LED rear tail lights
    • Product Link™ PRO with three year subscription
    • Remote jump start post
    • Resettable main and critical function breakers
  • Operator Environment
    • Cab, pressurized
    • 75 mm (3 in) retractable seat belt, with audible alarm and indicator
    • Automatic temperature control
    • External heated mirrors with lower parabolic
    • Hydraulic control lockout
    • Ground level cab door release
    • Suspension seat, fabric
    • Lunch box storage
    • Radio ready speakers
    • Rear window defrost, electric
    • Mirror, single
    • Column mounted multi function control – lights, wipers, turn signal
    • Tilt and telescopic steering wheel
    • Tinted front glass
    • Wet arm wiper/washer, 2-speed and intermittent, front, lights, wipers, turn signal
    • Camera, rear view
  • Other Standard Equipment
    • Cat optimized Z-bar linkage with parallel lift
    • Large-access enclosure doors with adjustable close/open force
    • Recovery hitch, with pin
    • Remote mounted lubrication points
    • Lockable compartments and enclosures

Optional Equipment

  • Optional Equipment
    • Auto lube, integrated in secondary display
    • Auxiliary flow, third and fourth function
    • Beacon light, strobe
    • Cab, deluxe (standard in Europe)
      • Camera, rear view integrated into advanced display
      • Electrically adjustable external heated mirrors (2)
      • Secondary display to enable features and adjust parameters
      • LED interior lighting
      • Sunscreen, front and rear
      • Touchscreen secondary display
      • Ride control adjustable speed activation
      • Preventative maintenance reminders
      • Integrated help function (26 languages)
    • Camera, roof mounted, front view with separate display
    • Cat Production Measurement weigh scale system integrated into secondary display
    • Cold start package
      • Ether starting aid, block heater and additional batteries, 1,000 CCA (4 total)
    • Coupler, (Fusion and ISO 23727)
    • Fenders (extended cover and full coverage)
    • Differential, limited slip, rear
    • Guarding packages
    • Lights, auxiliary, halogen or LED with engine and DEF compartment lights
    • Linkage, high lift
    • Payload Technology
      • Cat Production Measurement (CPM)
      • CPM Printer
    • Product Link ELITE with capabilities for software push, data logging, histogram and trend mapping
    • Radio packages
    • Ride Control System, adjustable through secondary display
    • Seats
      • Deluxe seat – fully adjustable fabric air suspension seat with mid seat backrest
      • Premium seat – fully adjustable leather and fabric air suspension with high backrest and air lumbar support. Seat is heated and ventilated on bottom cushion and backrest.
    • Steering
      • Dual mode and secondary
    • Tire Pressure Monitoring (TPM)
    • Counterweight, additional options
    • Debris packages (low, medium, high)
    • Rear Object Detection