Cat 908 Compact Wheel Loader

Maximum Gross Power

74.7HP

Engine Model

Cat C2.8*

Maximum Engine Speed

2550 rpm

Maximum Gross Power – Rated Engine Speed

2400r/min

Maximum Gross Power – SAE J1995

74.7HP

Maximum Gross Power – ISO 14396

74.3HP

Maximum Gross Power – ISO 14396 (metric)

75.3mhp

Rated Net Power – Rated Engine Speed

2400r/min

Rated Net Power – SAE J1349

72.7HP

Rated Net Power – ISO 9249

72.1HP

Rated Net Power – 2,400 rpm – ISO 9249 (metric)

73.1mhp

Maximum Gross Torque – SAE J1995

222lb/ft

Maximum Gross Torque – ISO 14396

221lb/ft

Maximum Net Torque – SAE J1349

218lb/ft

Maximum Net Torque – ISO 9249

217lb/ft

Displacement

171in³

Bore

3.54in

Stroke

4.33in

Note

Advertised power is tested per the specified standard in effect at the time of manufacture

Note (1)

Net power advertised is the power available at the flywheel.

Note (2)

*Two Cat C2.8 engine emission options are available: 1) Meets U.S. EPA Tier 4 Final, EU Stage V. 2) U.S. EPA Tier 3 and EU Stage IIIA equivalent. Tier 3 engine specs are 0.3 kW/0.4 hp more gross power (SAE J1995), 0.2 kW/0.3 hp on net power (SAE J1349)

Note (3)

#Maximum gross and net torque measured at 1,600 rpm.

Operating Weight

14617lb

Bucket Capacities

0.75-1.55 m³ (1.0-2.0 yd³)

Bucket Capacities – General Purpose

0.80-1.35 m³ (1.0-1.7 yd³)

Multi-Purpose

0.75-1.1 m³ (1.0-1.4 yd³)

Bucket Capacities – Light Material

1.25-1.55 m³ (1.6-2.0 yd³)

Note

Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.

Note (1)

Bucket capacities stated include BOCE, in line with ISO 7546.

Recyclability

93%

Fuel Tank

24Gal

Cooling System

3.2Gal

Engine Crankcase

2.3Gal

Axles – Front Center Differential

2.3Gal

Axles – Rear Center Differential

2.3Gal

Hydraulic System – Including Tank

18.6Gal

Hydraulic Tank

11.8Gal

Transmission

0.6Gal

Note

No Diesel Exhaust Fluid (DEF) fluid needed on this size engine.

Front

Fixed (standard), Locking Differential (optional)

Rear

Fixed (standard), Locking Differential (optional)

Note

Oscillation of ±11 degrees via hitch between front and rear frames.

Steering Articulation Angle – Each Direction

39°

Maximum Flow – Steering Pump

12.3gal/min

Maximum Working Pressure – Steering Pump

3336psi

Steering Cycle Times – (full left to full right) – at High Idle

2.8s

Number of Steering Wheel Turns – Full Left to Full Right or Full Right to Full Left

3.25 turns or 4.00 turns

Forward and Reverse – Speed Range Creep#

6mile/h

Forward and Reverse – Speed Range 1*

6mile/h

Forward and Reverse – Speed Range 2** – High Speed

10.5mile/h

Forward and Reverse – Speed Range 2** – Standard

12mile/h

Forward and Reverse – Speed Range 3***

25mile/h

Note

#Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).

Note (1)

*Creep function not available in this gear or above.

Note (2)

**Max speed dependent on model and configuration (standard vs. high speed transmission).

Note (3)

***Reverse is 30 km/h (19 mph).

Tire Size – Standard

*405/70 R20 SPT9

Tire Size – Optional

405/70 R20 Powerloads

Tire Size – Optional (1)

400/70 R20 XMCL/Bibload

Tire Size – Optional (2)

360/80 R20 TRI 2

Tire Size – Optional (3)

40X14-20 TL, SM/TR

Note

*This tire has been used for all dimension, stability and performance data.

Note (1)

Other tire choices are available. Contact your Cat dealer for details.

Note (2)

Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.

ROPS

ISO 3471:2008

FOPS

ISO 3449:2005 Level II

Note (1)

Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.

Main Relief – 1st Auxiliary (3rd slice)

3408psi

Main Relief – 1st Auxiliary (3rd slice) – Standard Flow*

24gal/min

Main Relief – 1st Auxiliary (3rd slice) – High Flow*

33gal/min

Main Relief – 2nd Auxiliary (4th slice)

3408psi

Main Relief – 2nd Auxiliary (4th slice) – Flow

12gal/min

Hydraulic Cycle Time – Rackback

2.5s

Hydraulic Cycle Time – Lift

5.8s

Hydraulic Cycle Time – Dump

1.8s

Hydraulic Cycle Time – Float Down

3.6s

Note

* Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display.

Height: Ground to Cab**

8.75ft

Height: Ground to Beacon**

9.33ft

Height: Ground Axle Center**

1.67ft

Height: Ground Clearance**

1ft

Length: Overall*

18.17ft

Length: Rear Axle to Bumper

4.5ft

Length: Hitch to Front Axle

3.5ft

Length: Wheel Base

7.08ft

Clearance: Bucket at 45° *

8.58ft

Clearance: Load over Height**

9.75ft

Clearance: Level Bucket**

10.5ft

Height: Bucket Pin**

11.17ft

Height: Overall**

14.17ft

Reach: Bucket at 45° *

2.33ft

Carry Height: Bucket Pin

1.17ft

Dig Depth**

0.33ft

Width: Bucket

6.75ft

Width: Tread Center

5.08ft

Turning Radius: Over Bucket

14.75ft

Width: Over Tires

6.67ft

Turning Radius: Outside of Tires

13.17ft

Turning Radius: Inside of Tires

6.5ft

Rack Angle at Full Lift

53°

Dump Angle at Full Lift

45°

Rack Angle at Carry

51°

Departure Angle – Degrees

30°

Articulation Angle – Degrees

39°

Operating Weight: Bucket ^

14633lb

Tipping Load – Straight – ISO 14397-1 †

10626lb

Tipping Load – Full Turn – ISO 14397-1 †

8895lb

Operating Weight: Carriage and Tines ^^

14252lb

Tipping Load – Straight †

10626lb

80% of Tip: Firm and Level EN474-3 ††

5815lb

Note (1)

*Vary with bucket

Note (2)

**Vary with tire

Note (3)

^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.

Note (4)

^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5)

†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6)

††Full compliance to EN474-3 and SAE J1197.

Note (7)

#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (8)

Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class II

Note (9)

Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9

Length: Front Axle to Front of Coupler

3.92ft

Height – Ground to Cab

8.75ft

Height: Ground to Beacon**

9.33ft

Height: Ground Axle Center**

1.67ft

Height – Ground Clearance

1ft

Length – Overall with Bucket

18.67ft

Length: Rear Axle to Bumper

4.5ft

Length: Hitch to Front Axle

3.5ft

Length – Wheel Base

7.08ft

Clearance – Bucket at 45°

8.25ft

Clearance: Load over Height**

9.75ft

Clearance – Level Bucket

10.5ft

Height – Bucket Pin

11.17ft

Height: Overall**

14.42ft

Reach – Bucket at 45°

2.67ft

Carry Height: Bucket Pin

1.25ft

Dig Depth

0.45ft

Width – Bucket

6.75ft

Width – Tread Center

5.08ft

Turning Radius – Over Bucket

15.08ft

Width – Over Tires

6.67ft

Turning Radius: Outside of Tires

13.17ft

Turning Radius – Inside Tire

6.67ft

Rack Angle at Full Lift

50°

Dump Angle at Full Lift

48°

Rack Angle at Carry

54°

Departure Angle – Degrees

30°

Articulation Angle – Degrees

39°

Operating Weight: Bucket ^

14752lb

Tipping Load – Straight – ISO 14397-1 †

9581lb

Tipping Load – Full Turn – ISO 14397-1 †

8141lb

Operating Weight: Carriage and Tines ^^

14391lb

Tipping Load – Straight †

9753lb

80% of Tip: Firm and Level EN474-3 ††

5438lb

Note (1)

*Vary with bucket

Note (2)

**Vary with tire

Note (3)

^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.

Note (4)

^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5)

†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6)

††Full compliance to EN474-3 and SAE J1197.

Note (7)

#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (8)

Note (9)

Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9

Tipping Load – Full Turn – ISO 14397-1†

6800lb

Length: Front Axle to Front of Coupler

4.75ft

Height: Ground to Cab**

8.75ft

Height: Ground to Beacon**

9.33ft

Height: Ground Axle Center**

1.67ft

Height: Ground Clearance**

1ft

Length: Overall*

19.67ft

Length: Rear Axle to Bumper

4.5ft

Length: Hitch to Front Axle

3.5ft

Length: Wheel Base

7.08ft

Clearance: Bucket at 45° *

10.92ft

Clearance: Load over Height**

10.75ft

Clearance: Level Bucket**

12.08ft

Height: Bucket Pin**

12.75ft

Height: Overall**

15.67ft

Reach: Bucket at 45° *

3.25ft

Carry Height: Bucket Pin

1.17ft

Dig Depth**

0.33ft

Width: Bucket

6.75ft

Width: Tread Center

5.08ft

Turning Radius: Over Bucket

15.83ft

Width: Over Tires

6.67ft

Turning Radius: Outside of Tires

13.17ft

Turning Radius: Inside of Tires

6.5ft

Rack Angle at Full Lift

69°

Dump Angle at Full Lift

40°

Rack Angle at Carry

48°

Departure Angle – Degrees

30°

Articulation Angle – Degrees

39°

Operating Weight: Bucket ^

14848lb

Tipping Load – Straight – ISO 14397-1 †

9187lb

Tipping Load – Full Turn – ISO 14397-1 †

7645lb

Operating Weight: Carriage and Tines ^^

14542lb

Tipping Load – Straight †

9187lb

80% of Tip: Firm and Level EN474-3 ††

4706lb

Note (1)

*Vary with bucket

Note (2)

**Vary with tire

Note (3)

^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.

Note (4)

^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5)

†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6)

††Full compliance to EN474-3 and SAE J1197.

Note (7)

#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (8)

Note (9)

Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9

Height: Ground to Cab**

8.75ft

Height: Ground to Beacon**

9.33ft

Height: Ground Axle Center**

1.67ft

Height: Ground Clearance**

1ft

Length: Overall*

20.17ft

Length: Rear Axle to Bumper

4.5ft

Length: Hitch to Front Axle

3.5ft

Length: Wheel Base

7.08ft

Clearance: Bucket at 45° *

10.42ft

Clearance: Load over Height**

10.75ft

Clearance: Level Bucket**

12.08ft

Height: Bucket Pin**

12.75ft

Height: Overall**

15.92ft

Reach: Bucket at 45° *

3.42ft

Carry Height: Bucket Pin

1.25ft

Dig Depth**

0.42ft

Width: Bucket

6.75ft

Width: Tread Center

5.08ft

Turning Radius: Over Bucket

16.17ft

Width: Over Tires

6.67ft

Turning Radius: Outside of Tires

13.17ft

Turning Radius: Inside of Tires

6.5ft

Rack Angle at Full Lift

66°

Dump Angle at Full Lift

40°

Rack Angle at Carry

42°

Departure Angle – Degrees

30°

Articulation Angle – Degrees

39°

Operating Weight: Bucket ^

15070lb

Tipping Load – Straight – ISO 14397-1 †

8385lb

Tipping Load – Full Turn – ISO 14397-1 †

6943lb

Operating Weight: Carriage and Tines ^^

14714lb

Tipping Load – Straight †

8385lb

80% of Tip: Firm and Level EN474-3 ††

4375lb

Note (1)

*Vary with bucket

Note (2)

**Vary with tire

Note (3)

^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.

Note (4)

^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5)

†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6)

††Full compliance to EN474-3 and SAE J1197.

Note (7)

#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (8)

Note (9)

Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9

Power Train
- Emissions compliant, two options (Dependent on regional regulations.)
  – U.S. EPA Tier 4 Final and EU Stage V
  – U.S. EPA Tier 3 and EU Stage IIIA equivalent
- Cat C2.8 engine
  – Diesel particulate filter (Fit for Life) or muffler (Dependent on regional regulations.)
  – Fuel, diesel, ultra low or low Sulphur (Dependent on regional regulations.)
  – Hydrostatic transmission, two speed, with inching function, “shift on the go”
  – Power train mode, hystat
- Air cleaner, two stage filter, with in cab audio/visual indicator on display
- Axles, heavy duty, frame mounted with outboard planetary reduction
- Closed circuit breather
- Coolant, extended life, –36° C (–33° F)
- Drive shaft, sealed for life, universal joints
- Engine, auto idle shutdown, hibernation mode
- Engine oil, ECO drain tap and hose
- Fuel pump, priming (manual)/water separator/drain
Hydraulics
- Hydraulic pilot shut off switch, in cab
- Electro-hydraulic, fully proportional controls
- Dead engine lower, lift valve, manual
- Demand cooling fan, hydraulically drive
- Coupler/pin on attachment ready
- Caterpillar HYDO^™ Advanced 10 hydraulic oil
- Hystat displacement pump, infinitely variable
- Implement valve, pressure compensated
- Joystick, single lever, single auxiliary roller
- Multi-function lift and tilt with loader arm float
- Motor, single drive with dedicated implement and steering pumps
Electrical
- Alternator, 100 amp sealed
- Battery, heavy duty, 12V, 90Ah and 1,000 CCA
- Battery disconnect switch
- Cab mounted fuse panel
- Lights, rear stop and turn, LED
- Lights, roading, front halogen
- Service (Electronic Technician^™)
- Product Link^™
Operator Environment
- ROPS/FOPS certified canopy/cab
  – 12V power outlets, interior/exterior
  – Pedals, raised, foot, brake/inching, accelerator
  – Lever, parking brake
  – Cup holders (2)
  – CB radio clip, phone holder
  – Door release, internal (left and right)
  – Hook, large, coat and hard hat
  – Floormat, heavy duty, easy clean
  – Mirrors, (2) external breakaway, (1) internal
  – Operator station on isolation mounts
  – Steering wheel, spinner knob, horn in center
  – Seat belt, orange, retractable, 51 mm (2 in)
  – Storage, personal (trays [3], seat pocket)
  – Steering column, tilt adjusted
  – Column mounted multi function control: lights, roading, wipers, self cancelling turn signals
  – Quick coupler switch, in cab
- Display, analog and digital
  – Gauges (2), hydraulic oil, engine coolant
  – Digital with soft touch buttons – fuel level, speed range, speedometer, service hour meter, service/maintenance information, hydraulic and power train performance and aggressiveness settings, security passcode (multiple languages)
- Joystick, seat mounted, standard multifunction
  – FNR, auxiliary roller, speed range select, continuous flow, differential lock, horn
  – Arm rest, padded right, multiple position vertical height
- Seat, manual height adjustment, (cab) fabric with adjustable left arm rest, (canopy) vinyl
- Cab
  – Doors (2), fixed glass
  – Wipers, front and rear, full front coverage
  – Windshield, front single piece
  – Window, rear heated
  – Radio ready, speakers and wiring
  – Air vents, (4) screen, (7) directional
  – Heating, mechanical control unit
  – Sun visor, solid, front full width
  – Interior light (incandescent)
Other
- Fenders, front and rear
- Ground level easy access daily service points
- Loader arm safety brace
- Lockable main and side engine enclosures
- Lockable, fuel cap, HVAC filters, nose cone
- Machine lifting/tie down points
- Paint, Electro-Coat primer, gloss topcoat
- Recovery hitch with pin
- Scheduled Oil Sampling (S·O·S℠) ports, engine oil and hydraulic oil

Power Train
- Antifreeze, extended life coolant, –50° C (–58° F)
- Cold start – jacket water heater, bypass valve
- Creep and throttle lock function
- Fuel pump, priming, electric (Dependent on regional regulations.)
- 40 km/h (25 mph) hydrostatic transmission, 3-speed, “shift on the go”, secondary steering and boosted brakes
- Power train mode, utility (includes keypad)
Electrical
- Lighting packages, multiple; front, rear, engine bay (LED or HAL)
- Push to start
- Work tool wiring harness, (3) in cab switches
Hydraulics
- Auxiliary flow, single standard (3) valve, single high flow (3) valve, dual high flow (4) valve
- Caterpillar Bio HYDO Advanced hydraulic oil
- Connect under pressure and case drain
- Ride Control or load check valves*
- Reversing fan
- Quick disconnect auxiliary hydraulics
Operator Station
- Air Conditioning, automatic temperature control (ATC)
- Doors, sliding windows (left and right)
- Interior light, door activated
- Joystick, FNR, twin auxiliary roller, differential lock, horn
- Joystick, seat mounted, multifunction
- Mirrors (2) electronically adjustable, heated external, plus lower parabolic mirror
- Phone holder, spring loaded
- Radio, FM or digital audio broadcast
- Seat belt options, multiple
- Seat packages; deluxe or premium
- Secondary display, front or rear view camera
- Soft touch keypad options, 8 or 16 button
- Storage, lockable box or lockable cooled box
- Sun visor, rear perforated
- USB ports (2), interior
Other
- Couplers, vertical (SSL), horizontal (HPL-V, HPL-A)
- Rotary sensors (snubbing, kickouts, parallel)
- High lift option

Cat 908 Compact Wheel Loader

Why Choose Louisiana Cat

YOU MIGHT ALSO BE INTERESTED IN

Cat 908 Compact Wheel Loader

SHARE:

T315 High Flow Trencher with no chain

T315 High Flow Trencher with combo teeth

T315 High Flow Trencher with standard teeth

T315 High Flow Trencher with standard teeth

T112 Manual Trencher with standard teeth

T112 Manual Trencher with rockfrost teeth

T112 Manual Trencher with no chain

T112 Manual Trencher with combo teeth

T112 Hydraulic Trencher with standard teeth

T112 Hydraulic Trencher with combo teeth

T112 Hydraulic Trencher with no chain

T112 Hydraulic Trencher with standard teeth

T112 Hydraulic Trencher with rockfrost teeth

T109 Manual Trencher with standard teeth

T109 Manual Trencher with no chain

T109 Manual Trencher with standard teeth

T109 Manual Trencher with rockfrost teeth

T109 Manual Trencher with terminator teeth

T109 Manual Trencher with combo teeth

T109 Hydraulic Trencher with standard teeth

T109 Hydraulic Trencher with no chain

T109 Hydraulic Trencher with standard teeth

T109 Hydraulic Trencher with combo teeth

T109 Hydraulic Trencher with rockfrost teeth

T109 Hydraulic Trencher with terminator teeth

LT118 Landscape Tiller

LT114 Landscape Tiller

SG16 Stump Grinder

SW380, 250 mm (10 in) Wheel Saw

SW360, 80 mm (3 in) Wheel Saw

SW360, 160 mm (6 in) Wheel Saw

SW360, 200 mm (8 in) Wheel Saw

SW360, 130 mm (5 in) Wheel Saw

SW345, 130 mm (5 in) Wheel Saw

SW360, 100 mm (4 in) Wheel Saw

SW345, 80 mm (3 in) Wheel Saw

PR123 Hydraulic Angle Power Box Rake

PR121 Hydraulic Angle Power Box Rake

PR121 Manual Angle Power Box Rake

PR118 Hydraulic Angle Power Box Rake

PR118 Manual Angle Power Box Rake

LR119 Landscape Rake

LR116 Landscape Rake

Hydraulic Nursery Fork with Variable Adjustments

1148 mm (45 in) Tree Scoop Bucket

Manual Nursery Fork with Fixed Adjustments

0.76 m3 (1.0 yd3) Mulch Bucket with bolt-on cutting edge

Material Handling Arm For Compact Products

1312 mm (52 in) Pallet Fork Carriage

1312 mm (52 in) Pallet Fork Carriage

1438 mm (57 in) Heavy Duty Fork Carriage

CV117 Vibratory Drum Compactor

CV119 Vibratory Drum Compactor

PC310 High Flow XPS Cold Planer

PC306 With Water High Flow Cold Planer

PC306 High Flow Cold Planer

PC305 High Flow Cold Planer

PC105 Standard Flow Cold Planer

PC104 Standard Flow Cold Planer

BD121 Side Discharge Bucket With Sawdust Agitator

BD118 Side Discharge Bucket With Sawdust Agitator

BD121 Side Discharge Bucket With Sand Agitator

BD118 Side Discharge Bucket With Sand Agitator

MB250 Mixing Bucket

MB200 Mixing Bucket

0.9 m3 (1.2 yd3) Skid Steer Coupler Multi-Purpose Bucket With Bolt-On Teeth

0.9 m3 (1.2 yd3) Skid Steer Coupler Multi-Purpose Bucket With Bolt-On Cutting Edge

2080 mm (82 in) Skid Steer Coupler Industrial Grapple Bucket With Bolt-On Cutting Edge

1.1 m3 (1.4 yd3) Skid Steer Coupler General Purpose Bucket

BRX118 Industrial Brushcutter

BU121 Utility Broom with Polypropylene Bristles

BU118 Utility Broom with Polypropylene Bristles

BU115 Utility Broom with Polypropylene Bristles

BP22 Pickup Broom

BP118C Pickup Broom

BP115C Pickup Broom

BA121 Hydraulic Angle Broom With Polypropylene Bristles

BA22 Hydraulic, 12V Angle Broom